Know More Particulars About Fad0s9f1 Fault Detector Circuit

Know More Particulars About Fad0s9f1 Fault Detector Circuit

Since the FADOS9F1 is small in size, it is very easy to carry and you can carry it even in a briefcase. This kind of ecu fados tester makes your work easier and simpler. The other usage areas of this device include ECU Automotive Electronic Circuit Boards, medical devices circuit board, servo-step motor drivers, circuit boards of computer & monitor, circuit boards of television, radio & audio, electronic circuit boards of military & mobile phones, textile machine circuit boards and much more. It can also use to test electronic components like resistors, inductors, capacitors, diode, transistors, TRIAC�s, Integrated Circuits, SCR�s, Optocouplers, etc.

The 1st feature of this Fados9f1 C ircuit is the Programmable DC Power Supply which is adjustable and you can adjust the voltage and current with the output power. The voltage can be adjusted from 0 to 16V and the current can be adjusted from 20mA to 1500 mA and it will produce the V/I graph of the electronic power supply. The �IR Temperature Measurement Sensor� is its 2 nd feature and it is used to find the components which generate high temperature. By including these two features, the device helps to decrease the time of troubleshooting the malfunctions by five to ten minutes . This is also a very new technique of troubleshooting.

This technique is also dealt with the maximum voltage is made to be adjusting with the connection of power cable in the intact board input. Normally, This adjustment method is developed by the �Power Test� button, which provides desired result from 0 to 100mV voltage. The desired result is obtained to draw the graph and get the record if necessary. After few minutes, the desired result of voltage graph provides temperature map, which helps to IR sensor. Then the IR sensor is also used to calculate some other component temperature. An intact card graph is required to be testing only defected circuit board.

No other difference from VI testing device, FADOS device comes under the motor control, mobile phone, nd automotive sector, audio, video and medical sector. Other usages are developed to use and electronic components. FADOS9F1 TESTER helps to give accurate reliability and adjustment of troubleshooting in an electronic circuit. Then it can make without any apply power to the UUT device. It is used to avoid risk and also current processes come along with the consequential damage. No other materialized fluctuations will occur on the defective components, with short circuit or low impedance.

The device will determine the maximum current so as to produce the supply graph for the defective card. When the defective card is found to draw more current, the IR sensor will measure the temperature of the involved materials. This will help to find the particular material that draws too much current. When the defective card is found to draw less amount of current, then it is subjected to act as an open circuit. In these cases, the device will activate the oscilloscope screen to find the connection which is broken in the supply line.

FADOS9F1 is nothing but Fault Detector and Oscilloscope which consists of nine functions in a single device. It is also a computer-based voltage-current tester as well as VI C urve T ester. Normally it is recommended to use in large and medium laboratories to get an output of greater efficiency . The device is made to be developed as a V/I tester from ProT Ar-Ge which is the Industrial Project Design of L it is used to find the components to generate the high temperature. Above features are included in that device and it has to decrease huge amount time of troubleshooting to blemish at five to ten minutes. The IR temperature measurement sensor is a new troubleshooting technique.

In addition to the FADOS7F1, the FADOS9F1 offers two additional features such as programmable power supply as well as IR Temperature measurement of non-contact. The programmable power supply which is included in the product will be connected to the UUT powerlines to set a maximum voltage. Then the �test button� will be activated, the software included in the device will produce an output of 100mV which will step up to the maximum value. The voltage value and the current value will be made to save in a file. And the IR Temperature measurement will be done after some time which will be used to determine the component with high temperature as well as defect related.

In addition to the FADOS7F1, the FADOS9F1 offers two additional features such as programmable power supply as well as IR Temperature measurement of non-contact. The programmable power supply which is included in the product will be connected to the UUT powerlines to set a maximum voltage. Then the �test button� will be activated, the software included in the device will produce an output of 100mV which will step up to the maximum value. The voltage value and the current value will be made to save in a file. And the IR Temperature measurement will be done after some time which will be used to determine the component with high temperature as well as defect related.
Back to top